Your order is empty
Damper Installation Hardware
Low Leakage Control Dampers
An important way to stop energy loss is to replace old, leaky control dampers. Standard or custom sizes are quickly available to make your replacement or new installation as easy as possible.
CALL US! Specify your dimensions, type of damper and actuator you need. We have a complete assortment of Electric or Pneumatic operators and accessories in stock.
Ask For Our Exclusive “Quik-Spec” Delivery Program!
| DAMPER ORDERING INFORMATION | |
|---|---|
| FEATURE | DESCRIPTION |
| DAMPER TYPE | Parallel, Opposed, Smoke, etc. |
| DAMPER DIMENSIONS | Width, then height for square; Diameter for round |
| ACTUATOR MOUNT | Internal or External Post, Rotary, Direct Mount |
| ACTUATOR TYPE | Pneumatic, Electric, 4-20mA, 2-Position, Modulating, etc. |
| LINKAGES | See Damper Accessories, Section for Crankarms, Push Rods, Ball Joints, etc. |
Damper Linkage Kits
When you’re using electric motors to operate dampers, you have to use a damper linkage kit for mounting and coupling the motor to the damper.
| ORDERING INFORMATION | ||
|---|---|---|
| ORDER # | BRAND | DESCRIPTION |
| Q605D1069 | Honeywell | Motor Mounting Bracket, 3 Damper Arms, Motor Crankarm, 4 Balljoints |
| Y20DAB-2 | Johnson | Motor Mounting Bracket, Motor Crankarm, Damper Crank, 2 Balljoints, (1) 249 Push Rod |
DON’T FORGET!
Order an Electric or Pneumatic Actuator with your Dampers.
See the “ACTUATORS-ELECTRIC; PNEUMATIC” PAGES
LEAKY DAMPERS! A Major Energy Waster
When it’s real hot or real cold, it’s essential to keep unwanted, untreated air from entering the building. New low leakage dampers are the best answer. When that’s not possible, give your old dampers new efficiency with…
Pneuline Low Leakage Damper Blade Gaskets
Special formula polyethylene molded gaskets. Simply slip over the edge of the blade – it holds firmly. Standard eight (8') foot lengths cut to size easily.
| ORDERING INFORMATION | |
|---|---|
| ORDER # | DESCRIPTION |
| DG101 | 8' Polyethylene Damper Gasket |
Solid-State Damper Positioner Kit
Made of durable red clay. Simply place under the bottom damper blade for convenient outdoor air minimum positioning.
| ORDERING INFORMATION | |
|---|---|
| ORDER # | DESCRIPTION |
| BRICK 1 | 10% O.A. Positioner |
| BRICK 2 | 20% O.A. Positioner |
| DAMPER ACCESSORIES | |||
|---|---|---|---|
DAMPER ARM  |
ORDER # | PUSHROD 5/16" diameter pushrod available in various lengths.  |
ORDER # |
| DA716 For 7/16'' Shaft | PR24 (24'') | ||
| DA012 For 1/2'' Shaft | PR48 (48'') | ||
| BALLJOINT Straight type balljoint used for connecting drive arms to push rods. For 5/16'' push rods.  |
BJ516 | DAMPER BLADE BRACKET Attached to damper blade for connection to linkage.  |
AB125 |
| DAMPER ACCESSORY ORDERING INFORMATION | ||
|---|---|---|
| ORDER # | DESCRIPTION | FUNCTION |
| DMPR-KC211 | 2 Damper Jackshaft Kit | Connects 2 Dampers to the Same Actuator |
| DMPR-KC212 | 3 Damper Jackshaft Kit | Connects 3 Dampers to the Same Actuator |
| DMPR-KC152 | 90° Blade-to-Blade Linkage Kit | Drives 2 Dampers Joined at a 900 Angle |
| DMPR-KC250 | Manual Quadrant | To Manually Operate Dampers |
| DMPR-KC100 | Blade-to Blade Linkage Kit | Drives 2 Vertically Coupled Dampers |
| DMPR-KC151 | Blade-to-Blade Bracket Kit | Couples 2 Horizontally Joined Dampers |
| DMPR-KC101 | External Pin-to-Pin Linkage Kit | Drives Two Vertically Coup;led Dampers |
| DMPR-KC003 | 7" Pin Extension | Extends Length of the Blade Drive Pin |
| DMPR-KC150 | Blade-to-Blade Bracket Kit | Couples 1-NO and 1-NC Damper Joined Side-By Side |
Authorized distributor of more than 200,000 HVAC
parts & controls.
 |
| Join Our Mailing List |
My Account
NECC News
